Other language confidence: 0.5836594291574956
In this dataset we provide data for 6 experimental models of caldera collapse and subsequent resurgence monitored through geophysical sensors (a force or “impact sensor”, Piezotronics PCB 104 200B02 and a Triaxial piezoelectric accelerometer, Model 356B18). The analogue modelling experiments were carried out at the TOOLab (Tectonic Modelling Laboratory), which is a joint laboratory between the Istituto di Geoscienze e Georisorse of the Consiglio Nazionale delle Ricerche, Italy and the Department of Earth Sciences of the University of Florence. The laboratory work that produced these data was partly supported by the European Plate Observing System (EPOS), by the Joint Research Unit (JRU) EPOS Italia and by the “Monitoring Earth's Evolution and Tectonics” (MEET) project (NextGenerationEU). Specifically, this work was performed in the frame of the DynamiCal project, funded by the 2° TNA-NOA call of the ILGE-MEET project.
This dataset compiles quantitative outputs from eight sandbox experiments conducted under different boundary conditions (differential extension, strong blocks, and a weak zone). It contains 3-D scanning–derived digital elevation models (DEMs) from the final stage of experiments simulating the V-shaped opening of the South China Sea. In addition, it includes particle image velocimetry (PIV) products at four extension states (25 mm, 50 mm, 75 mm, and 100 mm), together with the plotting codes used to generate the figures.
This data set includes results from a total of 13 analogue tectonic models aimed at simulating the activation of tectonic lineaments associated with the Main Ethiopian Rift in eastern Africa. We use a model set-up based on previous work by Zwaan et al. (2021, 2022). This set-up involves a velocity discontinuity (VD, i.e., the edge of a mobile base plate) to induce extension in the overlying brittle- and viscous model materials representing the upper and lower crust, respectively. Additional structural weaknesses (seeds) at the base of the brittle layer serve to represent activated tectonic weaknesses in nature. Model parameters (different VD and seed orientation, and different seed diameters) are summarized in Table 1. The model results presented in this data publication are obtained through Digital Image Correlation (DIC) and Structure-from-Motion (SfM) analyses. A more detailed description of model set-up, model results, and their interpretation can be found in Zwaan et al. (2025)
In this dataset we provide top-view photos and perspective photos (to create topographic data, i.e. Digital Elevation Models, DEMs) documenting analogue model deformation. For more details on modelling setup, experimental series Wang et al. (2021), to which this dataset is supplementary material. For details on analogue materials refer to Del Ventisette et al., 2019, Maestrelli et al. (2020). The analogue modelling experiments were carried out at the TOOLab (Tectonic Modelling Laboratory) of the Institute of Geosciences and Earth Resources of the National Research Council of Italy, Italy, and the Department of Earth Sciences of the University of Florence. The laboratory work that produced these data was supported by the European Plate Observing System (EPOS) and by the Joint Research Unit (JRU) EPOS Italia. Additional analysis, following the original work, was supported by the “Monitoring Earth’s Evolution and Tectonics” (MEET) project
This data set includes videos depicting the surface evolution (time-lapse photography, topography data and Digital Image Correlation [DIC] analysis) of 11 analogue models, divided in three model series (A, B and C), simulating rifting and subsequent inversion tectonics. In these models we test how orthogonal or oblique extension, followed by either orthogonal or oblique compression, as well as syn-rift sedimentation, influenced the reactivation of rift structures and the development of new inversion structures. We compare these models with an intracontinental inverted basin in NE Brazil (Araripe Basin). All experiments were performed at the Tectonic Modelling Laboratory of the University of Bern (UB). We used an experimental set-up involving two long mobile sidewalls, two rubber sidewalls (fixed between the mobile walls, closing the short model ends), and a mobile and a fixed base plate. We positioned a 5 cm high block consisting of an intercalation of foam (1 cm thick) and Plexiglas (0.5 cm thick) bars on the top of the base plates. Then we added layers of viscous and brittle analogue materials representing the ductile and brittle lower and upper crust in our experiments, which were 3 cm and 6 cm thick, respectively. A seed made of the same viscous material was positioned at the base of the brittle layer, in order to localize the formation of an initial graben in our models. The standard model deformation rate was 20 mm/h, over a duration of 2 hours for a total of 40 mm of divergence, followed by 2 hours of convergence at the same rate (except for Models B3 and C3, since the oblique rifting did not create space for 40 mm of orthogonal inversion). For syn-rift sedimentation, we applied an intercalation of feldspar and quartz sand in the graben. Model parameters and detailed description of model set-up are summarized in Table 1, and results and their interpretation can be found in Richetti et al. (2023).
This dataset includes video sequences and strain analysis of 12 analogue models studying crustal-scale deformation and basin reactivation, performed at the Laboratory of Tectonic modelling of the University of Rennes 1. These models show how parameters such as crustal strength, tectonic inheritance and boundary conditions (shortening/ stretching) control both the distribution of crustal strain and the possibility for pre-existing structures to be reactivated. This dataset includes top-view movies of the 12 models, including strain analysis based on displacement vectors obtained from digital image correlation. Detailed descriptions of models can be found in Guillaume et al. (2022, special issue of Solid Earth on Analogue modelling of basin inversion) to which this dataset is supplementary.
This data set includes the results of digital image correlation analysis applied to nine experiments (Table 1) on magma-tectonic interaction performed at the Helmholtz Laboratory for Tectonic Modelling (HelTec) of the GFZ German Research Centre for Geosciences in Potsdam in the framework of EPOS transnational access activities in 2017. The models use silicone oil (PDMS G30M, Rudolf et al., 2016) and Quartz sand (G12, Rosenau et al., 2018) to simulate pre-, syn- and post-tectonic intrusion of granitic magma into upper crustal shear zones of simple shear and transtensional (15° obliquity) kinematics. Three reference experiments (simple shear, transtension, intrusion) are also reported. Detailed descriptions of the experiments can be found in Michail et al. (submitted) to which this data set is supplement. The models have been monitored by means of digital image correlation (DIC) analysis including Particle Image Velocimetry (PIV; Adam et al., 2005) and Structure from Motion photogrammetry (SfM; Donnadieu et al., 2003; Westoby et al., 2012). DIC analysis yields quantitative model surface deformation information by means of 3D surface topography and displacements from which surface strain has been calculated. The data presented here are visualized as surface deformation maps and movies, as well as digital elevation and intrusion models. The results of a shape analysis of the model plutons is provided, too.
This dataset is supplementary material to the article of Ritter et al. (2017). In this article, the similarity of fault propagation work in analogue sandbox experiments to natural fault networks is investigated through measurements in a strike-slip sandbox and in a ring-shear-tester. The transient shear strength of the samples is measured for different fault lengths and from this the work is determined. For a detailed description of the procedure and the set-up please see Ritter et al. (2017). The data available in this supplementary publication are: • For the strike-slip experiments three video sequences of the deformation together with the evolution of boundary force for fault lengths of 20 cm, 30 cm and 40 cm. The videos show the curl of the deformation field, determined by Digital Image Correlation of top-view video images. These files are in AVI-format and included in the zip folder 2017-005-Ritter-movies.zip. • A folder containing force vs. displacement measurements for each experiment (2017-005-Ritter-forces.zip). These are 25 ASCII-files that contain two columns of numerical data: the first column is the displacement in meter; the second column is the corresponding force in newton. The files are named according to the following pattern: <fault length in meter>_<experiment number>.asc • A Matlab script to load the force files and calculate the work. This file is called “plotwork.m” and calls the Matlab function “work.m”, which does the actual calculations. These files have been tested in Matlab version 2012b. The surface deformation data are available upon request.
This data publication includes animations and figures of eight scaled analogue models that are used to investigate the evolution of a curved mountain belt akin to the Pamir and Hindu Kush orogenic system and adjacent Tadjik basin. Crustal deformation is simulated by means of indentation of two basement blocks into a sedimentary sequence and the formation of a curved fold-and-thrust belt. The experimental set-up has two adjacent rigid indenters representing the basement blocks moving in parallel with a velocity difference (Figure 1). The slow indenter moves with a relative velocity ranging from 40 to 80% of that of the fast one. A layer of quartz sand in front of the indenters, 1 by 1 meter in size and 1.5 cm thick, represents the sedimentary basin infill. A basal detachment layer is made up of low-friction glass beads or viscous silicone oil representing weak shale or evaporates layers, respectively. The surface evolution by means of topography and strain distribution is derived from 3-D particle image velocimetry (PIV). This allows visualizing and analysing the development of the model surface during the complete model run at high spatio-temporal resolution. All details about the model set-up, modelling results and interpretation can be found in Reiter et al. (2011). The here provided additional material includes time-lapse movies showing the topographic evolution of the eight models. These visualizations are oblique views played back at 60-fold velocity for the “glass beads experiments” (gb40 to gb80) and 3600-fold velocity for the “silicone experiments” (si60, si-gb60). In addition to the experiment movies we provide a set of figures. The figures include surface views as well as cross-sections through the finite models highlighting the link between topography and internal structure of the simulated curved fold-and-thrust belts. Additionally, attribute maps of distinct morphometric measures (curvature, slope) and deformation parameters (uplift, horizontal translation) for the experiments with glass beads detachments are given. Finally, the movie “Experimenting.avi” shows in time-lapse the whole workflow of setting up, conducting and documenting an experiment, which originally required three days (for experiment si-gb60). An overview on the parameters used in the experimental series of the movie sequences is given in the explanatory file (Explanations_Reiter-et-al-2016.pdf). A full list of files is given in “list-of-files-Reiter-et-al-2016.pdf”.
This dataset includes raw data used in the paper by Reitano et al. (2020), focused on the effect of different analogue materials on the mechanical and erosional properties of some defined samples. The samples are mixes of three different analogue materials in various proportions. The experiments have been carried out at Laboratory of Experimental Tectonics (LET), University “Roma Tre” (Rome). Detailed descriptions of the experimental apparatus and experimental procedures implemented can be found in the paper to which this dataset refers. We used the MATLAB toolbox “TopoToolbox” (Schwanghart and Scherler, 2014). Here we present: - Pictures recording the evolution of the models. - Laser scans used for further analysis. - Scripts created ad hoc by the authors and used for analyzing and plotting the data. A detailed methodological description can be found in the associated "2020-021_Reitano-et-al_Dataset decription" pdf file.
| Organisation | Count |
|---|---|
| Wissenschaft | 12 |
| Type | Count |
|---|---|
| unbekannt | 12 |
| License | Count |
|---|---|
| Offen | 12 |
| Language | Count |
|---|---|
| Englisch | 12 |
| Resource type | Count |
|---|---|
| Keine | 12 |
| Topic | Count |
|---|---|
| Boden | 7 |
| Lebewesen und Lebensräume | 5 |
| Mensch und Umwelt | 11 |
| Wasser | 7 |
| Weitere | 12 |