Other language confidence: 0.9604792228233349
Objective: Methane derived from solid biofuels is an important option for achieving the political goal for an increased use of alternative motor fuels. The biomass methanation has already been demonstrated on the small scale. And methane can easily be feed into the existing Natural Gas infrastructure, and can then be used with available technology, in particular within vehicle fleets. Although this option has been explicitly encouraged by the EC Directive 2003/55/EC so far no R&D-focus has been put on this. Thus, the objective of this project is it to realise and demonstrate the production of Synthetic Natural Gas (SNG) from solid biofuels within an innovative, large scale gasification plant to be built in Austria and to applicate this motor fuel in energy efficient vehicles (WTW).
We propose to initialise a European Network for observations of molecular Hydrogen and to put in place a new and consistent calibration scale for molecular Hydrogen. The observational network will have 12 continuous measurements sites in Europe, 7 flask sampling sites in Europe and 6 global flask sampling sites. Concerning the European sites, a range of observation from clean air stations for measurements of atmospheric background to moderately polluted (e.g. urban outflow) and urban (i.e. polluted) sites was chosen. This will enable to improve the understanding of hydrogen in the global background atmosphere and of the impact of European emissions on the present day atmosphere, e.g. using local modelling techniques and radon flux calculations. We further propose to perform budget studies of molecular hydrogen (on a global and regional scale) and to study sinks and sources. Especially the important soil sink will be studied (mechanistically and experimentally). A first systematic study of isotopic composition of molecular hydrogen in the atmosphere is proposed, using observations from global and European flask sampling sites and global models, which hydrogen isotope fractionation processes will be incorporated. Global and regional models will be used to investigate the budget of atmospheric hydrogen, by comparing mixing ratios and isotope ratios between model and observations and by varying underlying model emission patterns. The Proposal further includes some studies to assess the impact of atmospheric hydrogen on the present day atmosphere, i.e. the influence on the oxidation capacity of the troposphere, the lifetimes of greenhouse gases like CH4 and on the stratospheric budgets of water vapour and ozone. Some exploratory studies will be carried out to investigate these impacts under changed atmospheric hydrogen levels, associated with the use of hydrogen as a carrier of economy.
Objective: The project aims to develop highly integrated solar heating and cooling systems for small and medium capacity applications which are easily installed and economically and socially sustainable. The envisioned applications are residential houses, small office buildings and hotels. The goal is to use the excess solar heat in summer to power a thermally driven cooling process in order to provide cooling for air-conditioning. In the heating season the solar system is used to provide direct heating. The proposed project therefore aims to demonstrate the technical feasibility, reliability and cost effectiveness of these systems, specially conceived as integrated systems to be offered on the market as complete packages which will make better use of the available solar radiation as present systems.
Objective: The project focuses on the demonstration of an innovative and sustainable CHP concept using residues from olive oil production (olive wastes) as fuel. A first plant based on the new concept will be realised in Greece. The main objective of the project is to demonstrate a closed cycle concept able to reduce landfill problems and emissions and to promote the use of renewable electricity production in Southern Europe. The project will be based on an approach integrating the whole chain (fuel logistics and preparation, energy production, by-product utilisation). An optimised fuel logistic concept will guarantee for a secured fuel supply over the whole year. The fuel will not only be dewatered and dried but also a marketable by-product will be produced. By this means a better fuel quality can be achieved and solid wastes as well as waste- water can be omitted. The development and design of the combustion unit focuses on a technology tailored to the special characteristics of the olive waste.
Objective: The results of the project will improve and widen the potential for the integration of solar (PV) energy systems into existing buildings. Special attention will be paid architectural and aesthetic questions. Building integration of PV systems in most cases leads to a 'high tech' and 'modern' appearance of the building. This is caused by the typical window-like surface of most conventional PV modules. Regarding however that90Prozent of the building stock consists of longer existing, that means 'old fashioned' buildings, it is evident that anaesthetically satisfying building integration of PV needs a lot of good will and creativity from planners and architects. In many existing building integrated PV systems the modules contrast with the building and its surroundings. A European survey on the potential and needs for building integrated PV components and systems will identify the basis for the development of modules away from the glass / window-like appearance. In the project PV roof tiles, overhead glazing and facade elements based on CIS thin film technology will be developed and investigated which have a modified optical appearance for better adaptation to the building skin. One of the ideas is optical decoupling of substrate and cover glass. A complete roof tile system with thin film cells adapted to the visual appearance of conventional roof tiles and innovative connection and mounting will be developed. The work includes prototype fabrication and tests according to relevant standards and subsequent performance tests. Novel overhead glazing includes semitransparent thin film modules optimised for daylight transmission. The backside appearance will be modified in order to represent the visible inner part of the building skin. For overhead and insolating glazing an invisible interconnection and for PV roof tiles a low cost connector will be developed. Project results will be systems ready for industrial production.
Objective: The proposed project is designed to address the problem of pollution of the environment by road vehicles as denned under the Thematic Priority 1.6.2, Sustainable Surface Transport relating to the Work Programme 'Integrating and strengthening the European Research Area'. The research activities of the consortium will be based around state of the art developments in the area of optical fibre sensor and intelligent instrumentation technology to formulate a system for on line monitoring of exhaust emissions from road vehicles. The application of this technology to resolving the problems of atmospheric pollutants and their regional impacts is therefore highly appropriate to the issue identified in the thematic roadmap i.e. 'New technologies and concepts for all surface transport modes'. The consortium which will execute the research programme comprises six members from four EC member states. They include four academic institutions, an SME and an end user (a major European car manufacturer). Their combined expertise and knowledge of the technological and business issues will facilitate the rapid development of the technology into a demonstratable prototype within the three year lifetime of the project. The project's technical objectives are summarised as follows: -. To set up laboratory based test facilities such that the sensor systems may be characterised in a precisely controlled and reproducible manner. Therefore, individual parameters such as optical absorption and scattering may be studied in isolation as well as collectively.. To isolate and identify the optical signals arising from contaminants present in the complex mixtures of exhaust systems of a wide range of vehicles using advanced and novel optical fibre based spectroscopie interrogation techniques. To develop novel optical fibre sensors which are miniature and robust in their construction and may be fitted...
Objective: The aim of this demonstration project is to put to practical test, in a pipeline of working size, the thermal and resistance reducing properties found to be possessed by friction inhibitors (surfactants) in the laboratory. The results are intended to determine the practical potential of micellar friction inhibiters. General Information: The project will use an existing 450 mm bore pipeline, 2400 m. in length, connecting the fenne thermal power station in Volklingen with a central heating station. The heat transfer water is pumped by two rotary pumps with a maximum capacity of 2000 Cu.M/H. Heat is introduced by three independantly controlled heat exchangers at the power station. The effect of the friction-inhibiting additives will be determined by fitting temperature and differential pressure recorders and an inductive flow meter (diaphragm meters will not perform with friction inhibitors in the water). Pressure measurements will be taken at elbows and U-bends to obtain information on how the additives affect behaviour in these sections of the pipe. The use of surfactants will enable existing remote heating systems to convey a greater quantity of thermal energy through an existing network or to convey the same amount with reduced pumping costs. In new installations they will reduce the capital costs by enabling smaller pipes to be used for a given flow rate.
Objective: Reduction of energy costs in drying of packing varnishes through a recovery of process heat from the combustion of recovered solvents and its utilization for heating the drier plant. The calculated energy savings are assumed to amount to approx. 4500000 kW/year. General Information: The innovative technology consists of a combination of individual technological solutions. These include the condensation of solvents, the drying of packing varnish, thermal post-combustion of the exhaust air from the plant (which is rich in carbohydrates), heating of this port-combustion system by using the solvent condensate as fuel, and the utilization of the resulting energy (i.e., pure exhaust air exhibiting a very high temperature) as process heat for drying of packing varnish. Overall plant structure: Evaporation section with heat exchanger and vacuum extraction system; Measuring device for monitoring the solvent concentration; Condensation system for recovery of incoming solvents; Preheating zone with heat exchanger and extraction system; Daking section with heat exchanger and extraction system; Post-combustion system for generating process heat through combustion of the recovered solvents; Cooling section; Air recirculation system between the different sections. This combination of system components causes the exhaust air volume (and hence, the total carbohydrate release rate) to be drastically reduced. The investment cost of this combine plant is about twice as high as that of a conventional system. On the other hand, the total annual energy generating cost for a conventional plant exceeds that of the combined plant by a factor of 1.5. This means that the combined system achieves cost savings between DM 150000 and DM 180000 per year. Assuming that the proceeds from a conventional systems and the combination plant are the same, the capital recovery from a plant of the type envisaged in the project is markedly higher (due to the lower total cost), which considerably shortens the period of amortization. Achievements: The technical and chemical feasibility of the project described in the application could be demonstrated with the conclusion of the design phase. A number of aspects have arisen, however, which may turn the project into a financial failure on the current level of information. One of these facors is the draft of the Accident Prevention Rules for Lacquer Driers (VBG 24) of March 1988, which calls for a considerable reduction in admissible solvent concentrations compared to the older version of these Accident Prevention Rules. With these new, reduced solvent concentrations, the recovery of solvents through condensation is no longer an economically viable proposal. Moreover, the Ministry of the Environment expects the packaging industry to make increasing use of low-solvent lacquers. Renowned packaging manufacturers are already using low-solvent or water soluble varnishes. Plants designed for such applications have already been...
General Information/Summary: The aim of this proposal is the technological development of dye photovoltaic cells, recently invented by the Swiss Institute of Technology (EPFL), from today's laboratory stage to highly reliable and reproducible products and to become producible by an industrially feasible manufacturing process. Dye PV cells will be optimized for indoor applications where laboratory cells have already shown promising I-V and stability performance. Through such applications, this new thin-film PV technology may be introduced to the market place even before the turn of the century, create new jobs in Europe and, ultimately, smooth the way for the technically more demanding outdoor applications. The high economical and ecological interest of such an approach relies on the increasing importance of stand-alone indoor power systems with a market potential in the order of 1 billion modules per year and the replacement of non-rechargeable batteries by a more sustainable technology. The new PV technology will directly challenge the Japanese domination in the field of amorphous silicon cells. Specifically, dye PV cells will be designed for the fast growing market of electronic price labels in retail stores that fulfil the specifications of the end user with regard to power/size ratio, costs and mechanical requirements. Dye PV cells have the potential to offer more than twice the power output of commercial amorphous silicon cells of a given size and to be produced at relatively low costs. The calculation of cost prices of industrially produced raw materials and dye PV cell manufacturing will be a principle objective for the industrial partners. A pilot line for assembling up to 1 mio. PV modules (ca. 2.5 V) per year will be designed, allowing for a complete estimation of production costs. In order to achieve the goals of the present proposal within the planned 24 months, a consortium of academic (EPFL, University of Uppsala) and institutional R and D laboratories (ECN, IVF), a large chemical manufacturer (DSM)t a specialist on glass/polymer and other polymer film based compounds (L.P.M.), a manufacturer of electrochemical storage devices (Leclanche) and an and user (Pricer) producing electronic price labels have joined forces. The RTD programme is subdivided in nine well-defined tasks, including PV cell specification, first prototype preparation, optimization for the end user's requirements, characterization, final cell preparation to ultimately the design of a pilot production line and testing of the final dye PV cells in two retail stores. Netherlands Energy Research Foundation; Petten/Netherlands.
Objective: The aim of Wingy-Pro is to demonstrate the first ever large size transversal flux generator in an existing wind turbine. A determining factor for increasing the profitability of an offshore wind farm is the installation of wind turbines with a significantly high power capacity and low weight. Until now, the designs of large capacity turbines for offshore applications have been an up scaling of the existing smaller models. This has led to the construction of wind turbines with huge physical dimensions (e.g.: The E-112 has a hub height of 124 m and a rotor diameter of 114 m). Consequently, the weight of the turbines has increased considerably and the material-resistance of the blades, has been taken almost to its limits (rotor blades can reach a length of up to 61 m). These large dimension and weight have a negative influence on the economic efficiency of those offshore applications, because of the high costs for the foundation, transport and installation of the wind turbines. The objective of the project is to carry out the design and development of an improved generator technique through the transverse flux generator (TFG) with permanent magnets in the rotor. There are single-, two- or multi-phase machines, depending on the number of independent stator windings, which are mounted axially on the machine shaft. This technique has been known in the electro-field for years, but due to its strong vibrations and high noise emissions, it has been hardly used. Nowadays however, thanks to new and innovative manufacturing methods and to the development in modern micro-processing controls, the TFG can be used in practical applications.
| Organisation | Count |
|---|---|
| Bund | 403 |
| Europa | 400 |
| Kommune | 3 |
| Land | 1 |
| Wirtschaft | 1 |
| Wissenschaft | 126 |
| Type | Count |
|---|---|
| Förderprogramm | 403 |
| License | Count |
|---|---|
| Offen | 403 |
| Language | Count |
|---|---|
| Deutsch | 22 |
| Englisch | 392 |
| Resource type | Count |
|---|---|
| Keine | 347 |
| Webseite | 56 |
| Topic | Count |
|---|---|
| Boden | 304 |
| Lebewesen und Lebensräume | 347 |
| Luft | 255 |
| Mensch und Umwelt | 403 |
| Wasser | 281 |
| Weitere | 403 |