Other language confidence: 0.9812575214187785
In this dataset we provide top-view photos and perspective photos (to create topographic data, i.e. Digital Elevation Models, DEMs) documenting analogue model deformation. For more details on modelling setup, experimental series Wang et al. (2021), to which this dataset is supplementary material. For details on analogue materials refer to Del Ventisette et al., 2019, Maestrelli et al. (2020). The analogue modelling experiments were carried out at the TOOLab (Tectonic Modelling Laboratory) of the Institute of Geosciences and Earth Resources of the National Research Council of Italy, Italy, and the Department of Earth Sciences of the University of Florence. The laboratory work that produced these data was supported by the European Plate Observing System (EPOS) and by the Joint Research Unit (JRU) EPOS Italia. Additional analysis, following the original work, was supported by the “Monitoring Earth’s Evolution and Tectonics” (MEET) project
This data set includes the results of high-resolution digital elevation models (DEM) and digital image correlation (DIC) analysis applied to analogue modelling experiments. Twenty generic analogue models are extended on top of a rubber sheet. Two benchmark experiments are also reported. Detailed descriptions of the experiments can be found in Liu et al. (submitted) to which this data set is supplement. The data presented here are visualized as topography and the horizontal cumulative surface strain (principal strain and slip rake).
This data set includes videos depicting the surface evolution of 29 analogue models on crustal extension, as well as 4D CT imagery (figures and videos) of two of these experiments. The experiments examined the influence of the method for driving extension (orthogonal or rotational) on the interaction between rift segments using a brittle-viscous set-up. All experiments were performed at the Tectonic Modelling Laboratory of the University of Bern, Bern, Switzerland (UB). Brittle and viscous layers are both 4 cm thick, extension velocities are 8 mm/h so that a model duration of 5 h yields a total extension of 40 mm (e = ca. 13%, given an initial model width of ca. 30 mm). Next to the mode of extension (orthogonal or rotational), we also test the effect of the degree of onderlap (angle φ). Detailed descriptions of the experiments and monitoring techniques can be found in Zwaan et al. (2020).
This data set includes videos depicting the surface evolution (time-lapse photography, topography data and Digital Image Correlation [DIC] analysis) of 11 analogue models, divided in three model series (A, B and C), simulating rifting and subsequent inversion tectonics. In these models we test how orthogonal or oblique extension, followed by either orthogonal or oblique compression, as well as syn-rift sedimentation, influenced the reactivation of rift structures and the development of new inversion structures. We compare these models with an intracontinental inverted basin in NE Brazil (Araripe Basin). All experiments were performed at the Tectonic Modelling Laboratory of the University of Bern (UB). We used an experimental set-up involving two long mobile sidewalls, two rubber sidewalls (fixed between the mobile walls, closing the short model ends), and a mobile and a fixed base plate. We positioned a 5 cm high block consisting of an intercalation of foam (1 cm thick) and Plexiglas (0.5 cm thick) bars on the top of the base plates. Then we added layers of viscous and brittle analogue materials representing the ductile and brittle lower and upper crust in our experiments, which were 3 cm and 6 cm thick, respectively. A seed made of the same viscous material was positioned at the base of the brittle layer, in order to localize the formation of an initial graben in our models. The standard model deformation rate was 20 mm/h, over a duration of 2 hours for a total of 40 mm of divergence, followed by 2 hours of convergence at the same rate (except for Models B3 and C3, since the oblique rifting did not create space for 40 mm of orthogonal inversion). For syn-rift sedimentation, we applied an intercalation of feldspar and quartz sand in the graben. Model parameters and detailed description of model set-up are summarized in Table 1, and results and their interpretation can be found in Richetti et al. (2023).
This data set includes images and videos depicting the evolution of deformation and topography of 17 analogue experiments c passive margin development, to better understand the ongoing tectonics along the western margin of Afar, East Africa. The tectonic background that forms the basis for the experimental design is found in Zwaan et al. 2019 and 2020a-b, and references therein. The experiments, in an enhanced gravity field in a large-capacity centrifuge, examined the influence of brittle layer thickness, strength contrast, syn-rift sedimentation and oblique extension on a brittle-viscous system with a strong and weak viscous domain. All experiments were performed at the Tectonic Modelling Laboratory of of the Istituto di Geoscience e Georisorse - Consiglio Nazionale delle Ricerche (CNR-IGG) and of the Earth Sciences Department of the University of Florence (CNR/UF). The brittle layer (sand) thickness ranged between 6 and 20 mm, the underlying viscous layer, split in a competent and weak domain (both viscous mixtures), was always 10 mm thick. Asymmetric extension was applied by removing a 1.5 mm thick spacer at the side of the model at every time step, allowing the analogue materials to spread when enhanced gravity was applied during a centrifuge run. Differential stretching of the viscous material creates flexure and faulting in the overlying brittle layer. Total extension amounted to 10.5 mm over 7 intervals for Series 1 models that aimed at understanding generic passive margin development in a generic orthogonal extension setting, whereas up to 16.5 mm of extension was applied for the additional Series 2 models aiming at reproducing the tectonic phases in Afar. In models involving sedimentation, sand was filled in at time steps 2, 4 and 6 (i.e. after 3, 6 and 9 mm of extension). Detailed descriptions of the experiments, monitoring techniques and tectonic interpretation of the model results are presented in Zwaan et al. (2020c) to which these data are supplementary.
This data set includes videos depicting the surface evolution (time-lapse photographs and Particle Image Velocimetry or PIV analysis) of 38 analogue models, in five model series (A-E), simulating rift tectonics. In these experiments we examined the influence of differently oriented mantle and crustal weaknesses on rift system development during multiphase rifting (i.e. rifting involving changing divergence directions or -rates) using brittle-viscous set-ups. All experiments were performed at the Tectonic Modelling Laboratory of the University of Bern (UB). The brittle and viscous layers, representing the upper an lower crust, were 3 cm and 1 cm thick, respectively, whereas a mantle weakness was simulated using the edge of a moving basal plate (a velocity discontinuity or VD). Crustal weaknesses were simulated using “seeds” (ridges of viscous material at the base of the brittle layers that locally weaken these brittle layers). The divergence rate for the Model A reference models was 20 mm/h so that the model duration of 2:30 h yielded a total divergence of 5 cm (so that e = 17%, given an initial model width of ca. 30 cm). Multiphase rifting model series B and C involved both a slow (10 mm/h) and fast (100 mm/h) rifting phase of 2.5 cm divergence each, for a total of 5 cm of divergence over a 2:45 h period. Multiphase rifting models series D and E had the same divergence rates (20 mm/h) as the Series A reference models, but involved both an orthogonal (α = 0˚) and oblique rifting (α = 30˚) phase of 2.5 cm divergence each, for a total of 5 cm of divergence over a 2:30 h period. In our models the divergence obliquity angle α was defined as the angle between the normal to the central model axis and the direction of divergence. The orientation and arrangements of the simulated mantle and crustal weaknesses is defined by angle θ (defined as the direction of the weakness with respect to the model axis. An overview of model parameters is provided in Table 1, and detailed descriptions of the model set-up and results, as well as the monitoring techniques can be found in Zwaan et al. (2021).
This data set includes the results of digital image correlation of ten brittle-viscous experiments on crustal extension and four benchmark experiments performed at the Tectonic Modelling Lab of the University of Bern (UB). The experiments demonstrate the differences in rift development in orthogonal versus rotation extension. Detailed descriptions of the experiments and monitoring techniques can be found in Zwaan et al. (2019) to which this data set is supplementary. Additional background information concerning the general modelling approach are available in Zwaan et al. (2016).. The data presented here consist of movies displaying digital image correlation (DIC) derived surface and internal displacement fields as well as profiles of the lateral cumulative surface displacements.Digital photographs of the experimental surface and digital image cross section of the computed CT-scans were analyzed with DIC (Adam et al., 2005, 2013) techniques to quantify displacements in the image plane at high precision (<0.1 mm). DIC was undertaken with the software DaVis 8.0 (LaVision) applying 2D-DIC (FFT-legacy) multipass processing with a final interrogation window size of 32x32 (CT: 12x12) pixels and 50% (CT: 25%) overlap.
In this dataset we provide data for 6 experimental models of caldera collapse and subsequent resurgence monitored through geophysical sensors (a force or “impact sensor”, Piezotronics PCB 104 200B02 and a Triaxial piezoelectric accelerometer, Model 356B18). The analogue modelling experiments were carried out at the TOOLab (Tectonic Modelling Laboratory), which is a joint laboratory between the Istituto di Geoscienze e Georisorse of the Consiglio Nazionale delle Ricerche, Italy and the Department of Earth Sciences of the University of Florence. The laboratory work that produced these data was partly supported by the European Plate Observing System (EPOS), by the Joint Research Unit (JRU) EPOS Italia and by the “Monitoring Earth's Evolution and Tectonics” (MEET) project (NextGenerationEU). Specifically, this work was performed in the frame of the DynamiCal project, funded by the 2° TNA-NOA call of the ILGE-MEET project.
This data set includes 40 videos (+ 1 image) depicting the surface evolution of 39 experiments on crustal extension, as well as 4D CT imagery (figures and videos) of 6 of these experiments. The experiments examined the influence of the method for driving extension (foam base, rubber base, plate base or conveyor base) for localization of deformation in overlying layers of brittle-only and brittle-viscous materials representing the earth’s crust. All experiments were performed at the Tectonic Modelling Laboratory of the University of Bern. Detailed descriptions of the experiments and monitoring techniques can be found in Zwaan et al. (2019) to which these data are supplementary material.All experiments were monitored with top view photographs (SLR camera Nikon D-100 6.1 MPx). The photograph time steps depend on the applied extension velocity, but are generally 1 or 2 min. Six experiments were also monitored with an X-Ray computed tomography technique using a 64 slice Siemens Somatom Definition AS X-ray CT-scanner (Zwaan et al., 2016) with varying time intervals (5-30 min). CT-data was analyzed with the software OsiriX (Pixmeo SARL).
This data set includes results from a total of 13 analogue tectonic models aimed at simulating the activation of tectonic lineaments associated with the Main Ethiopian Rift in eastern Africa. We use a model set-up based on previous work by Zwaan et al. (2021, 2022). This set-up involves a velocity discontinuity (VD, i.e., the edge of a mobile base plate) to induce extension in the overlying brittle- and viscous model materials representing the upper and lower crust, respectively. Additional structural weaknesses (seeds) at the base of the brittle layer serve to represent activated tectonic weaknesses in nature. Model parameters (different VD and seed orientation, and different seed diameters) are summarized in Table 1. The model results presented in this data publication are obtained through Digital Image Correlation (DIC) and Structure-from-Motion (SfM) analyses. A more detailed description of model set-up, model results, and their interpretation can be found in Zwaan et al. (2025)
| Organisation | Count |
|---|---|
| Wissenschaft | 10 |
| Type | Count |
|---|---|
| unbekannt | 10 |
| License | Count |
|---|---|
| Offen | 10 |
| Language | Count |
|---|---|
| Englisch | 10 |
| Resource type | Count |
|---|---|
| Keine | 10 |
| Topic | Count |
|---|---|
| Boden | 5 |
| Lebewesen und Lebensräume | 3 |
| Luft | 1 |
| Mensch und Umwelt | 9 |
| Wasser | 7 |
| Weitere | 10 |